A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Were you searching for resources about How to Install a Bathtub Yourself?
Mounting a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a new one is likewise a moderately tough task. If the old bathtub is conveniently easily accessible, the project can relocate easily; if you have to open up a wall to eliminate the old tub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. See to it you have qualified on your own for the job and also fit trying it. Rather than working with a professional to take over a halfway-completed job, it is far better to think about using one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will assist you set up a new tub in your bathroom if you have currently purchased a new bathtub as well as do not require to transform the arrangement of your previous water system pipelines.
Your tools and also material checklist must comprise the following:
Getting ready for the Setup
First of all, the supporting structure provided with the bath must be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipelines have been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed setting. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at the very least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers remain in area between the faucet as well as the sink. Safeguard the faucet in position with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former type ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily offered on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed reading the entire piece. Sharing is caring. One never knows, you may be doing someone a favor. Thank you for your time. Please stop by our website back soon.
Apply Now Report this page